Showing posts with label vw. Show all posts
Showing posts with label vw. Show all posts

Saturday, March 7, 2015

Cleaning up holes in the 1969 VW Beetle Wheel Wells...Still...

I'm still learning to weld. Earlier, I cut out bad metal and fit in new metal. This is my effort at plug welding small holes and welding metal on top of fragile 50 year old sheet metal. I am working with adjusting the heat, spooling wire and etc.

I cut new sheet metal to fit. Drilled holes and welded them in place. 

I will buy some sealer to prevent water from coming in. This VW has lots of sealer in place from the factory. I had to grind it off, but will replace it later.




This is inside the car looking at the wheel well.
This is the sheet metal I cut out to fit
Here is the outside wheel well with the sheet metal welded in




Monday, June 2, 2014

The Front Apron

Lots of Bondo and dents in the front apron
I worked for 5 to 8 hours with hammers and chisels to straighten out my bent and rusty front apron. My plan was to have a new one welded in, but I thought I might be able to fix it the old fashioned way.

However, once complete, it looked like Swiss cheese as fatigued metal snapped, rust broke through and Bondo popped out.

Torn metal found under old bondo and fiberglass.
I had the same experience with the rear apron. I was able to pound out a lot of damage and make it look halfway descent, but the amount of work yet to do was daunting.

Hours of relentless banging and pounding produced nothing but headaches. Time for a change in plan.

I decided to buy a welder and attempt to make the repairs myself. My next logical step is to review welders on line, determine what I needed, take some lessons and make it happen.

Still have about an inch more to remove before I weld.
Removing the front and rear apron required drilling out the old spot welds. Some are harder to see than others, so you might not know that old welds remain until you try to remove the skin. I used a hammer and chisel to remove the skin and chiseled out the remaining welds. Be very careful to not damage the skin on the main car. It's easy to gouge the metal, so if you err, make sure you damage the sheet metal that you are removing.
Just dreaming of what it will look like once I get it welded on.

For the front apron I used an electric saw with a blade meant to cut sheet metal. It went fast. There's a danger to fast as mistakes can happen faster than you can react. 

Friday, March 28, 2014

Finishing Some Chasis Work





I cleaned all the rotors on the outside to make them look nice and hold off on future rust until I can buy new rotors. Since the work is pretty easy, I'll save the new brakes and rotors until the project is done. I used a drill with a wire brush attachment to clean the rotors. I ground all the surface rust off, cleaned and painted with high temperature black caliper paint. They really look good.


The chassis is pretty much done where rust has been ground out and small holes repaired with POR-15 paint and fiberglass matting. A strong, waterproof bond on the floor pan is what's left. I've removed  most of the bolts, cleaned an repainted them as well. The only thing I couldn't get done was the removal and installation of the CV boots. Those bolts are just too tight and I keep stripping the star fittings.

My last chassis project is the wheels. I went to the local tire changing shop (Top-Line Tires) and paid $5.00 each to remove five tires. My plan is to clean the paint and rust off the rims and repaint in ivory powder coating. I read there is a company htat will do that for me, but online prices were $200 to $1000 per wheel. I'll take this project on myself.
I brought the wheels home and applied an environmental
citrus paint remover product called Citristrip. After the first application, I waited 24 hours and scrubbed with a wire sponge. I applied a second and third application before I was satisfied. The process worked great and now all I have to do is get some deep rust of a few of the r
ims.


Saturday, February 1, 2014

Looking for Dirt-Cleaning up the 1969 VW Chassis


I am undertaking tremendous work (at least for a beginner). Although I feel that I am diving in deep, I could probably go deeper, but not sure how. So, for now, I'll stick to the stuff I can see. 

I've got the chassis separated from the body, making it so much easier to focus on getting to parts I need to either replace or clean. So, my focus for the next few weeks is with the chassis. 


40 years of grime have built up. There is at least a 1/4 inch of grease, grime and dirt built up on the floor pan, suspension and steering. Everything in the front end and bottom side is normally not visible, but when the body is off; oh man:

Font steering and suspension before cleaning (view from
trunk) lots of grime here

Driver side front. Super clean now, but rusted. 


For the past few weeks, I've been de-greasing, pressure washing and wire brushing everything. The results of hacking away at 40 years of grime are clean parts. It's nice to see them somewhat restored.

I have removed the tie rods and shocks, steering and heater components. I am currently replacing them with replacement parts and cleaning up what I can salvage.

Many parts are being thoroughly cleaned and painted with high gloss black. The more rusted areas are cleaned and painted with POR 15 paint with makes a strong compound with rust.  Here's what I have so far. Doesn't it look better?

Front suspension and steering components

Rear floor plan and torsion bar

Front passenger wheel assembly

Driver side front floor pan and suspension

Saturday, November 16, 2013

Taking out and replacing side windows

Brand new rubber
dresses the glass up nicely
 I ordered two seals for my back side windows. The old VW is getting a face lift. Maybe not so much a face lift as a nice shot of BOTOX around the eyes. These new seals look great and will make my bug like new once finished.

After the trial and error experiencing removing both the rear and front glass, I found an easier way to to take out the windows. After pulling of the aluminum trim, cut the old seal all the way through the trim's channel.  Next cut between the window and seal (lift the rubber and slip the carpet knife blade in and slice to meet the cut you made in the channel). This will allow you to remove just the part of the seal holding the window in. Press the window gently from the inside and it should pop out. Next, just remove the old seal.

The channel for the new
aluminum trim
Where it took almost and hour to install the new seal around the back window, I developed a rhythm and method. The second window took about 30 minutes and the third window to 10 minutes. Use the same technique I mentioned earlier. This time you will be able to feel what is right and what works. Practice makes you faster. I'm looking forward to seeing how fast I get the windshield done. 


Saturday, March 23, 2013

Good looking dash area-Bamboo shelf for 69 VW Beetle


I just received the bamboo shelf from Jbugs.com I ordered recently. It got here in no time and looks really nice and I can’t wait to use it. I set it up just above my drink holder as well. I can’t wait to actually be able to keep the bug clean on the inside by the storage space concealed under the dash board. It looks really good too.

Beetle parts never come with instructions, so you have to search them out. This bamboo shelf came with four shelf brackets and 8 screws. I was planning to drill and screw, but a thought occurred to me; why not see if it fits.

It did fit and looks great. The best news is I didn’t have to use the hardware. For some reason the shelf fits so snug (I believe it is the thick carpet) that it is in for good. I’ll test it on the road and make sure it doesn’t vibrate loose. But for now, it looks solid.



I’ll be moving speakers and radio to different locations so the bamboo shelf can be better featured.














Wednesday, March 13, 2013

The Trunk

Newly painted area. Rug is pulled back to reveal fuel tank
I painted the entire trunk with Miracle Paint. It did the job of sealing the trunk's rust holes and improving the overall appearance. So far, so good.


Trunk before painting
I will have to buy new carpeting to cover some of the aesthetics of mismatched wires and random cables but it should look great once complete.

I ordered fresh air box and defrost hoses. I'm waiting for the defrost hoses that run to the heater channels and once they come in, can assemble the entire deal. The cleaning process is described in another post.

I ordered a new seal for the fresh air box. I’m hoping this will prevent the water from covering in that caused all the rust in the first place. This seal fits between the trunk and the box, making it water tight.

Old Box
Once the seal arrived, I tried to install it. That’s when I discovered the box was broken around the seal. The owner had silicon glued the seal in place, but it didn’t fit correctly and allowed water to drain in.



New Box
Fortunately I was able to find a decent used one (couldn’t find any in the obvious online stores, but a friend of a friend had one). The only thing is I forgot how to put the fresh air box back in. Everything works, but I just have to install it correctly. 






Monday, March 4, 2013

Fixing Rust


Huge gaping rusting holes. That’s all I can say about this project. Actually, this is only in the one area, right under the rear cargo storage area. I pulled back the carpeting and insulation to discover the rotting mess.

After some online research I found a wonderful product called Miracle Paint. A few thin coats of that on the fiber glass mesh and viola, instant metal, or a close proximity. The repair was successful and I don’t have the burnt oil and exhaust fumes leaking in any more.

Here’s how you get to it:

Remove the back seat and back rest.

For the bench, just pull up on the front and pull out. The seat just slides out.

For the back rest, you’ll need to remove two bolts at either end. Then pull off the carpet and insulation. Chances are that these will be glued down and you’ll replace them. I spent about $200 on mine from www.westcoastmetric.com (includes carpet for entire interior and the insulation).

Grind down the metal a bit. You can leave some rust and apply rust restoration spray from the  auto parts store.

A shop vac comes in handy to clean up the 50 years of dirt, dust, food and whatever is hanging around under the seats.

Then apply the miracle paint onto the mesh. Be sure to pre-cut the mesh to fit the repair area.





Saturday, February 16, 2013

Proud new owner


I just bought a 69 VW Beetle from a man who restored it to driving condition. I love driving it around, but it still needs some work. I bought it for $1500 and understood it may still need some “polishing”. I am enjoying fixing it up and learning how it works. I’ll use this blog to share our story.

First things first and that’s safety. I drove my kids around the block and one of the dry rotted tires went flat. I called around to see what would fit and none of the big box companies could help. They didn’t understand the small tire size. It wasn’t until I called Big 10 Tires that they could help me out. I had to go a little wider, but there were able to put the right ones on. When I pulled up with the bug, I got the royal treatment. They loved my car.

Now that I’ve got new tires, I drove around to work and around the neighborhood. I got a lot of thumbs up and encouragement. It’s so nice. However, I have to find out what’s making me dizzy.

Apparently exhaust has been leaking into the cabin, so I climbed in back to see what was up. It wasn’t until I removed the rear luggage storage carpet and insulation material that I discovered the deal; rusted floor pan.

Next I rip out the entire interior and find more rust and holes. At the same time I go into the trunk to find out what could be causing air to rush in through my ash gray and other areas.

I also discover water standing under the trunk carpeting. The problem; A missing drain hose from the fresh air box. I follow that line and do research and discover that it’s a large problem; water and air leaks through this system.

In the mean time, I’ve been making small improvements by replacing old control knobs on the dash and the horn ring and cover on the steering wheel.









Here are my favorite stores online:
www. westcoastmetric.com
www. jbugs.com
http://www.vw-wagenwerks.com/servlet/Categorieswww.wolfsburgwest.com

Visit often as I will document my journey to a further restoration of this magnificent car.